| Id | Name | Description | Brand | Price |
|---|
| HEASC1 | IRDASC-1 2 aspect LED signal operation |
These units operate 2 aspect LED signals on one board | Heathcote Electronics | 38.00 |
| HEASC2 | IRDASC-2 aspect bulb operation |
Same outputs as IRDASC-1 operates both bulb or LED signals | Heathcote Electronics | 40.00 |
| HEASC3 | IRDASC-3 2 aspect bulb or LED signal with isolatio |
Has a double pole relay for operating bot signal & isolating the track in front of the signal | Heathcote Electronics | 42.00 |
| HEASC4 | IRDASC-4 3 aspect signal |
These units operate 3 or 4 aspect signals. The signal aspect depends upon the aspect of the next signal or the presence of a train in the next section. The unit may either follow a MAS-SEQUENCER or be part of a chain of IRDASC-4 units. These units are special order depending on whether 3 or 4 aspect or common positive or negative wiring - allow approx 3 weeks for delivery. | Heathcote Electronics | 42.00 |
| HEASC5 | IRDASC-5 3 or 4 aspect bulb or LED signal with iso |
This works as described for the IRDASC-4 with the addition of a relay to provide track isolation when the signal is at red. These units are special order depending on whether 3 or 4 aspect or common positive or negative wiring - allow approx 3 weeks for delivery. | Heathcote Electronics | 44.00 |
| HE-PSM | IRDOT Slo-Mo point Control |
| Heathcote Electronics | 40.00 |
| HE01 | IRDOT-1 LED & electronic switch |
The basic unit. This lights a (control panel) LED. It has an electronic "train detected" switch to activate our other units where itemid = a second green "not detected" LED where itemid = or a relay. It is also possible to operate a bicolour LED to give for example green "not occupied" where itemid = red "occupied". | Heathcote Electronics | 29.00 |
| HE01D | IRDOT-1D LED & electronic switch with 4 sec delay |
Outputs are identical to the IRDOT-1. It detects the train immediately but takes 4 seconds to undetect where itemid = this is to provide continuous detection of the train. As a train crosses the IRDOT-1 the LED will flicker off at each gap between wagons or coaches where itemid = the IRDOT-1D''s LED will remain lit during these gaps due to the 4 second delay. | Heathcote Electronics | 31.00 |
| HE02 | IRDOT-2 Relay for stopping trains in sidings |
This operates an LED and a built-in changeover relay. It allows precise stopping of a train in hidden sidings. | Heathcote Electronics | 31.00 |
| HE02D | IRDOT-2D IRDOT2 with delay |
This has the same outputs as the IRDOT-2 where itemid = but also has a 4 second undetect delay to prevent the LED flickering and the relay repeatedly switching as the train travels over it. It can also be used to store trains in a row. | Heathcote Electronics | 32.00 |
| HE03 | IRDOT-3 LED & double pole relay |
This has a built in double pole relay and the facility to also operate both detect and undetect LED''s or a bicolour LED.. The size and voltage specifications are the same as the IRDOT-3D. | Heathcote Electronics | 38.00 |
| HE03D | IRDOT-3D ORDOT3 plus delay |
As the above with the addition of the following selectable delays: 3 where itemid = 6 where itemid = 9 where itemid = 12 where itemid = 15 where itemid = 18 where itemid = 21 where itemid = and 24 seconds. These are selectable by connection to the terminal block. | Heathcote Electronics | 40.00 |
| HE-P | IRDOT-P Solenoid Point Control |
This operates solenoid (PECO SEEP etc) point motors on detecting a train. It also has a train detected LED. These units can be used to operate automatic reverse loops and storage sidings. | Heathcote Electronics | 40.00 |
| HEMAS | MAS-SEQUENCER-4 2 where itemid = 3 or 4 aspect sig |
Designed to work with IRDASC-4 where itemid = This operates a 3 or 4 aspect signal on an adjustable time system. | Heathcote Electronics | 42.00 |
| HE105 | Point Indicator Relay |
| Heathcote Electronics | 58.00 |
| Id | Name | Description | Brand | Price |
|---|
| HE112 | 2 Latching Relay Board |
Can be used to control signals where itemid = reversing track power etc. 2 double pole relays | Heathcote Electronics | 40.00 |
| HE110 | 2 Relay Board |
2 double pole relays | Heathcote Electronics | 35.00 |
| HE113 | 4 Latching Relay Board |
Can be used to control signals where itemid = reversing track power etc. 4 double pole relays | Heathcote Electronics | 65.00 |
| HE111 | 4 Relay Board |
4 double pole relays | Heathcote Electronics | 59.00 |
| HE106 | Automatic route selector |
Automatically switches points to direct trains over 4 possible routes | Heathcote Electronics | 40.00 |
| HE115 | Diamond Crossing Protector |
Detects trains on the main line sets branch line signals to red where itemid = and isolates section of track before and after the crossing | Heathcote Electronics | 42.00 |
| HE102 | Direction Detector |
Senses which direction a train is moving and switches train | Heathcote Electronics | 40.00 |
| HE101 | Dual Delay Timer |
Two timer circuits to switch relays for an adjustable time | Heathcote Electronics | 45.00 |
| HE114 | Level Crossing Flasher |
Operates flashing lights on a level crossing | Heathcote Electronics | 42.00 |
| HE103 | Point Indicator |
Indicates which way points are set - will indicate up to 4 sets of points | Heathcote Electronics | 40.00 |
| HE104 | Point Indicator SO |
More powerful than standard Point Indicator. Switches a number of relays | Heathcote Electronics | 44.00 |
| HE116 | Variable Speed Clock |
Digital variable speed fast clock | Heathcote Electronics | 80.00 |
| Id | Name | Description | Brand | Price |
|---|
| SA6 | Automatic operation of storage sidings |
Requires 2 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 70.00 |
| SA7-SB | Block section with signal |
Requires 2 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 70.00 |
| SA4-S | Passing loop for oval |
Two trains run alternatively around an oval. Each waits at passing loop for the other train to arive before departing in the opposite direction. Requires 4 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 90.00 |
| SA5 | Passing loop for oval - unidirectional |
Same as SA4-S but with trains going in same direction. Requires 3 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 80.00 |
| SA5-S | Passing loop for oval - unidirectional - with sign |
Same as SA5 and operates a signal. Requires 3 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 85.00 |
| SA4 | Shuttle for passing loops |
Allows two trains running in opposite directions to pass. Requires 8 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 85.00 |
| SS | Simple Shuttle |
Shuttles trains back and forth with a 10 second pause at each end | Heathcote Electronics | 45.00 |
| SA1 | Single Line Shuttle |
Requires 4 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 70.00 |
| SA1-S | Single Line Shuttle - Operate Signal |
Requires 4 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 80.00 |
| SA3 | Single line shuttle with passing loop for two tra |
Requires 8 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 90.00 |
| SA2-S | Single Line Shuttle with sidings and signal at eac |
Requires 8 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 90.00 |
| SA2 | Single Line Shuttle with sidings at each end |
Requires 6 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 80.00 |
| SA1-1 | Single Line Shuttle with Station Stops |
Requires up to 8 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 75.00 |
| SA8-S | Station stop with signal |
Same as SA8 where itemid = and operates signal. Requires 2 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 80.00 |
| SA9 | Station stop with signal & block section |
Same as SA08-S able to control block section. Requires 2 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 85.00 |
| SA8 | Station stop with timer |
Requires 2 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 75.00 |
| SA10 | Two siding shuttle with one train |
Requires 5 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 85.00 |
| SA9 | Two track shuttle with point operation |
Requires 5 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 85.00 |
| SA9-S | Two train shuttle with point & signal operation |
Requires 5 * IRDOT NOTE: This unit is not compatable with DCC as it controls track voltage. | Heathcote Electronics | 90.00 |
Starter systems include the comprehensive installation and operations manual described as One of the best sources for DCC information. For the latest and most up to date pricing and help, please call to discuss your requirements.
| Id | Name | Description | Brand | Price |
|---|
| 12VT | 12VAC 1.5A plug in transformer |
| EasyDCC | 25.00 |
| 15PC005 | 22/44 pin edge card connector |
| EasyDCC | 15.00 |
| MOD7 | 6 Conductor 7 foot cable with plugs each end (telc |
| EasyDCC | 14.50 |
| AD4HC | AD4 High current for twin coil solenoid machines |
| EasyDCC | 79.00 |
| AD4MC | AD4 medium current for slow motion switch machines |
| EasyDCC | 69.00 |
| D7B7 | Booster 7amp dual zone |
| EasyDCC | 195.00 |
| S7B7-AR | Booster 7amp single zone |
| EasyDCC | 172.00 |
| RG58 | coaxial cable by the meter |
| EasyDCC | 2.00 |
| JACK | Coaxial PCB mount jack for fascia plates |
| EasyDCC | 2.00 |
| CS2TX | Command Station Transformer 12VAC / 500mA |
| EasyDCC | 25.00 |
| EDFK | Complete fascia plate board and connectors in kit |
| EasyDCC | 28.00 |
| EDFA | Complete fascia plate where itemid = board and co |
| EasyDCC | 32.00 |
| BSS4 | EasyDCC Basic Starter System |
Consists of Command Station where itemid = one booster 3 where itemid = and 7ft modular cable. You supply decoders (any brand) Powerpack or 16VAC extranal transformer for booster 3. Provides 2 fixed cabs - ready for later expansion | EasyDCC | 645.00 |
| EDBA | EasyDCC Booster 3 |
does not include power supply or connecting cables | EasyDCC | 128.00 |
| B5A | EasyDCC Booster 5 fully assembled |
| EasyDCC | 265.00 |
| ESS4 | EasyDCC Expanded Starter System |
Consists of Command Station where itemid = one Booster 3 where itemid = one throttle where itemid = one extender where itemid = and two 7ft modular cables. You supply decoders (any brand) Powerpack or 16VAC extranal transformer for booster 3. Provides 2 fixed cabs and one walk around throttle. | EasyDCC | 875.00 |
| MANUAL | EasyDCC printed and bound manual |
| EasyDCC | 30.00 |
| EDFP | Fascia plate alone (no connectors or PCB) |
| EasyDCC | 14.50 |
| DCPS120 | Fully assembled and wired 5A power supply |
| EasyDCC | 122.00 |
| EDXA | Throttle extender with 7ft modular cable |
| EasyDCC | 110.00 |
| PLUG | Twist on coax connector |
| EasyDCC | 3.00 |
| XR1300-4 | XR1300-4 Throttle complete ready to use |
| EasyDCC | 169.00 |
| SZB7-AR | ZoneMaster Booster 7amp Single zone with Autoverse |
| EasyDCC | 187.00 |
| ZS4X | ZoneShare Assembled without Case |
| EasyDCC | 268.00 |
| ZS4E | ZoneShare Deluxe Mounted in Case |
| EasyDCC | 352.00 |
| Id | Name | Description | Brand | Price |
|---|
| SilverMP | Silver MP Lenz Silver |
| Lenz | 50.00 |
| D13SR | D13SR Economy Decoder |
| North Coast Engineering (NCE) | 29.00 |
| D14SRP | D14SRP Plug and Play decoder |
| North Coast Engineering (NCE) | 45.00 |
| 1028 | 2 function plug and play |
| Train Control Systems (TCS) | 35.00 |
| 1000 | A4X 4 Function drop-in for HO diesels |
| Train Control Systems (TCS) | 42.00 |
| 1001 | A6X 6 Function drop-in for HO diesels |
| Train Control Systems (TCS) | 45.00 |
| 1028 | DP2X 2 function plug and play |
| Train Control Systems (TCS) | 36.00 |
| 1287 | Dp2X-UK 2 function plug and play |
| Train Control Systems (TCS) | 35.00 |
| 1028A | DP5X 5 function plug and play |
| Train Control Systems (TCS) | 35.00 |
| 1002 | FL2 Fleet Lighter 2 function |
| Train Control Systems (TCS) | 25.00 |
| 1004 | FL4 Fleet Lighter 4 function |
| Train Control Systems (TCS) | 27.00 |
| 1006 | M1 Micro 2 function hardwire |
| Train Control Systems (TCS) | 40.00 |
| 1009 | M3 3 function hardwired micro decoder |
| Train Control Systems (TCS) | 50.00 |
| 1011 | M4 4 function hardwired micro decoder |
| Train Control Systems (TCS) | 52.00 |
| 1019 | MC-6 6 function decoder |
| Train Control Systems (TCS) | 54.00 |
| 1013 | MC2 2 Function with micro connector |
| Train Control Systems (TCS) | 38.00 |
| 1014 | MC2-5 5pack of MC2 |
| Train Control Systems (TCS) | 175.00 |
| 1015 | MC2P-MH with medium harness |
| Train Control Systems (TCS) | 47.00 |
| 1115 | MC2P-SH with short harness |
| Train Control Systems (TCS) | 47.00 |
| 1017 | MC4 - 4 function decoder |
| Train Control Systems (TCS) | 45.00 |
| 1030 | MP-15N 4 function drop in for Atlas MP15 |
| Train Control Systems (TCS) | 54.50 |
| 1021 | T1 2 function with connector |
| Train Control Systems (TCS) | 30.00 |
| 1022 | T1 decoder with medium harness |
| Train Control Systems (TCS) | 35.00 |
| 1023 | T1A 2 function without connector |
| Train Control Systems (TCS) | 29.00 |
| 1104 | T1P-SH 2 function with short harness |
| Train Control Systems (TCS) | 35.00 |
| 1024 | T4X 4 function with connector |
| Train Control Systems (TCS) | 36.00 |
| 1026 | T6X 6 function with connector |
| Train Control Systems (TCS) | 42.00 |
| 1031 | VO-1000 4 function drop in for Atlas VO-1000 |
| Train Control Systems (TCS) | 54.50 |
| 1032 | VR1.5 1 where itemid = 5V regulated supply |
| Train Control Systems (TCS) | 16.00 |
| Id | Name | Description | Brand | Price |
|---|
| TT01 | Rrampmeter Version 1 |
| AHD Brand | 95.00 |
| TT02 | Rrampmeter Version 2 |
| AHD Brand | 148.00 |
| TT05 | Hare NG V2 Toroise Decoder |
| DCC Specialities | 54.95 |
| TT08 | On Guard DCC Autoreverser |
| DCC Specialities | 74.00 |
| TT07 | On Guard DCC Circuit Breaker |
| DCC Specialities | 57.50 |
| TT03 | PowerPax Programming Track Booster |
| DCC Specialities | 125.00 |
| TT06 | Wabbit Dual Tortoise Decoder |
| DCC Specialities | 44.50 |
| 79902 | decoder wire strippers 30 gauge |
| Expo | 34.50 |
| GV61 | Decoder wires set of 7 coloured 0.6m each |
| Gwydir Valley Models | 6.50 |
| GV62 | Kapton Tape 6mm wide 36 yards |
| Gwydir Valley Models | 0.00 |
| TT04 | PowerPax 18volt Power Supply |
| Gwydir Valley Models | 25.00 |
| TT09 | Throttle Pockets |
Suit most DCC throttles EasyDcc where itemid = Lenz where itemid = NCE where itemid = Digitrax | New Rail | 16.50 |
| N141P | Plug and Play Decoder |
| North Coast Engineering (NCE) | 45.00 |
| 6100 | Tortoise remote mount |
| Tortoise | 24.95 |
| 1038 | LH Long Harness |
| Train Control Systems (TCS) | 9.50 |
| 1049 | MCMH Medium Harness with NMRA Plug |
| Train Control Systems (TCS) | 9.50 |
| 1050 | MCSH Short Harness with NMRA plug |
| Train Control Systems (TCS) | 9.50 |
| 1039 | MH Medium Harness |
| Train Control Systems (TCS) | 9.50 |
| 1042 | SH Short Harness |
| Train Control Systems (TCS) | 9.50 |
| Id | Name | Description | Brand | Price |
|---|
| DSM100 | Bass Reflex 18*53*14mm 100ohm |
| Gwydir Valley Models | 21.50 |
| DSM8 | Bass Reflex 18*53*14mm 8ohm |
| Gwydir Valley Models | 21.50 |
| DLG100 | Bass Reflex 22*58*10mm 100ohm |
| Gwydir Valley Models | 21.50 |
| DLG8 | Bass Reflex 22*58*10mm 8 ohm |
| Gwydir Valley Models | 21.50 |
| 57120 | Enclosure Medium oval 20*35mm snap fir |
| Gwydir Valley Models | 18.95 |
| 570053 | Enclosure Round 0.75in (20mm) snap fit |
| Gwydir Valley Models | 14.50 |
| 570054 | Enclosure round 1.1in 28mm snap fit |
| Gwydir Valley Models | 14.50 |
| 57116 | Enclosure Small Oval 15*35mm snap fit |
| Gwydir Valley Models | 16.50 |
| 810112 | Speaker 25*15 mini oval 8ohm 1W |
| Gwydir Valley Models | 18.95 |
| DHB27-8 | Speaker High Bass 27*14 8 ohm |
| Gwydir Valley Models | 16.50 |
| DHB8 | Speaker High Bass 28*28*11mm 8ohm |
| Gwydir Valley Models | 16.50 |
| 60120 | Speaker Medium oval 20*35mm 8ohm 1W |
| Gwydir Valley Models | 14.50 |
| 60115 | Speaker oval 8 ohm 15*125mm |
| Gwydir Valley Models | 16.50 |
| 810053 | Speaker Round 0.75in (20mm) 8 ohm |
| Gwydir Valley Models | 16.50 |
| 60112 | Speaker round 1 1/8in 8 ohm with enclosure |
| Gwydir Valley Models | 12.95 |
| 810054 | Speaker round 1.1in (28mm) 8 ohm |
| Gwydir Valley Models | 16.50 |
| 60078 | Speaker Round 7/8in 8 ohm with enclosure |
| Gwydir Valley Models | 12.95 |
| 60166 | Speaker small oval 15*35mm 8 ohm 1 watt |
| Gwydir Valley Models | 14.50 |
